


Most limewash problems come from one of four causes: uneven suction in the wall, coats laid on too thick, a lost wet edge, or a substrate the lime was never going to bond to. Patchiness, chalking, streaking and flaking each trace back to one of those, and almost all of them are fixable without stripping the wall. Below is the list we get called about most, with the cause and what we actually do about it.
Would you rather have it done for you? Our own applicators provide limewash installation across the UK.
Worth saying at the start: limewash is meant to be uneven. Cloudiness, movement and a chalky bloom are the finish, not a fault. The problems here are the ones that look wrong rather than the ones that look like lime. If you are still deciding whether the material suits your wall, the limewash page covers that.
Cause. Uneven suction. Where the wall drinks hard, the limewash is pulled in and dries pale and thin; where it has been filled, sealed or previously painted, it sits on the surface and dries darker. Patched plaster is the usual culprit, followed by walls that were part primed or not primed at all.
Fix. Let the wall carbonate fully first, a good proportion of what looks patchy in week one settles by week three. If it is still blotchy after that, dust the wall down, apply a mineral primer to even the suction, and lay a further full coat of limewash. Do not spot treat the pale areas; you will simply swap one patchwork for another.
Prime every wall that has been filled or repaired, and damp the surface with clean water immediately before brushing. Both cost minutes and remove the single biggest cause of failure.
Cause. A little chalky dust in the first days is normal while the lime is converting. Heavy, persistent rub off means the coats were too thick, the material was over thinned, or the wall was too cold, too hot or too dry when it went on so the lime never carbonated properly. Lime needs moisture and air to harden; rush either and it stays dusty.
Fix. Buff the loose material off with a dry cloth or a soft brush, then apply one properly thin coat over a lightly dampened wall and let it cure in normal room conditions. If the surface is somewhere that gets handled, a hallway, a stairwell, a breathable mineral sealer will stop the dusting, at the cost of some of the matt bloom.
Cause. Parallel strokes rather than cross hatched ones, a starved or overloaded brush, or pressing too hard. Sharper, harder edged lines usually mean a lost wet edge. The material at the join had started to dry before the next band met it.
Fix. A full further coat, brushed properly: loose strokes one way, crossed at roughly a right angle, then softened at a third angle, with irregular stroke lengths. Work one whole wall in one go, top to bottom in a broad diagonal band, keeping the leading edge ragged rather than straight. Break at corners, never mid wall.
Keep sun, heat and draughts off the surface while you work.
Cause. This is the material behaving normally. Limewash is dark and saturated when wet and lightens clearly as the water leaves. It then lightens again over weeks as carbonation puts a fine chalky bloom across the surface.
Fix. If the colour is right but weak, a third coat builds density without changing the shade. If the colour is wrong, it needs a different tint rather than more of the same. Either way, prove it on a sample board first, brushed the same way and left several days. Judging a wet wall is what caused the problem in the first place. The colours page is the place to start again.
Cause. Limewash is a thin mineral film, not an opaque paint. It does not block out a dark background the way two coats of emulsion will, and it never will. Going pale over a strong colour, or over patchy repairs, is always a multi coat job.
Fix. Prime first, a mineral primer both evens the suction and lifts the base tone. Then build three thin coats rather than two thick ones. Thick coats do not increase opacity; they increase the risk of chalking and flaking. If you are going from something very dark to something very pale, accept that from the outset rather than discovering it on coat two.
Cause. Almost always the wrong substrate. Lime will not bond to a plastic film, so limewash over vinyl emulsion, gloss, or any sealed or waterproofed surface will let go in sheets. The other causes are a loose or dusty background that was never stabilised, coats laid far too thick, or trapped moisture pushing the film off from behind.
Fix. There is no shortcut here. Scrape back to a sound background, remove the old coating entirely where it is the problem, stabilise and prime the wall, and start again with thin coats. If moisture is driving it, fix the moisture before you put anything else on the wall. Related reading on coatings and substrates: can you paint over Venetian plaster.
Cause. Limewash is matt and mineral. It is not wipe clean, and it will mark where furniture, hands and hoovers meet it.
Fix. This is the easy one. Limewash repairs better than any painted finish: brush a fresh coat over the affected wall and it blends, because you are adding lime to lime rather than trying to match a plastic film. Keep a tub of the same tint from the original order for exactly this. Our general advice in how to maintain Venetian plaster applies to lime finishes across the board.
Recoat when the problem is cosmetic: patchy, streaky, too pale, marked. Strip and restart when the problem is adhesion, flaking, peeling, or lime over a sealed surface. Adding coats to a failing bond only buys you a heavier failure later.
If the material itself is the doubt, our tinted lime paint is tinted to your colour in the tub before it ships, which removes the batch and tint variables from the diagnosis and leaves you looking at the wall and the brush hand.
Usually uneven suction in the wall. Filled or repaired areas absorb differently from the surrounding plaster, so the lime dries at different densities. Let it carbonate for a few weeks first, because much of it evens out. If it is still blotchy, prime the wall with a mineral primer and apply one further full coat.
Buff the loose dust away, then apply one thin coat over a lightly dampened wall and let it cure in normal conditions rather than forced heat. Thick coats and over thinned material are the usual causes. Where a wall gets handled daily, a breathable mineral sealer stops the dusting, though it takes some of the chalky matt away.
Do the whole wall. Limewash blends beautifully coat to coat but poorly patch to patch, because the overlap dries at a different density and prints through. Full coats, one wall at a time, wet edge held throughout. The one exception is a small physical repair, which still wants the whole wall recoated afterwards.
Not over vinyl or gloss. Lime cannot bond to a plastic film and will flake. Over a sound, matt, porous emulsion it works if you first apply a mineral primer to provide grip and even the suction. If the existing paint is peeling or powdery, remove it rather than coating over it.
Where to go next: the limewash page explains the finish and where it belongs, tinted lime paint, primer and boards are all in the shop, and if a wall has gone wrong badly enough that you would rather hand it over, our own applicators cover the UK from Birmingham.
An outline of what limewash training covers about mixing limewash and the risks of slaking lime, and how to ask Zavoré about it.
BasementsA guide to decorative finishes for London basements, covering media rooms, gyms and wine rooms, why waterproofing must come first, and wh...
CheshireAn in depth guide to seamless microcement and tadelakt bathrooms for homes across Cheshire, and how to choose between them.
CheshireA guide to polished plaster and other decorative finishes for the large modern homes of Wilmslow and Alderley Edge, and where they fit in...
CheshireChester and the Cheshire countryside are full of timber framed, Georgian and Victorian buildings. This guide explains why lime finishes s...
Greater ManchesterHow microcement floors work in kitchen extensions across Greater Manchester, from the screed underneath to underfloor heating and everyda...
Providing luxury finishes for the most prestigious addresses in the world
Venetian plaster, limewash, microcement, tadelakt, metallics, sculptural plaster and gold leaf, supplied and installed by our own team, with Venetian plaster taught at our Birmingham studio.
One list, run by the people who make the material. No noise, and nothing we would not want to read ourselves.
We email as the house has something worth saying, never daily. Unsubscribe from any email, or reply STOP to any text. We never pass your details to anyone.