ZAVORÉ
ZAVORÉ
✦
Where Artistry Begins
Tracked delivery across the UK and worldwide·Same day and 24 hour delivery available·Venetian plaster tinted to your exact colour·Damaged in transit? We’ll replace it within 24 hours or on the same day·Speak to a specialist · 07592 929191·Residential and commercial projects installed by our own team·Trade accounts · 10% and rewards·Training courses at our studio·Showroom · visit by appointment·Tracked delivery across the UK and worldwide·Same day and 24 hour delivery available·Venetian plaster tinted to your exact colour·Damaged in transit? We’ll replace it within 24 hours or on the same day·Speak to a specialist · 07592 929191·Residential and commercial projects installed by our own team·Trade accounts · 10% and rewards·Training courses at our studio·Showroom · visit by appointment·
Home/The Journal/Mixing and Slaking Lime Safely, What the Lime Class Covers
16 November 2026

Mixing and Slaking Lime Safely, What the Lime Class Covers

Limewash training on mixing and slaking lime safely, close view of a white plaster wall with textured stucco

Short answer. Mixing limewash means thinning mature lime putty with clean water to the right consistency, adding any pigment evenly and keeping the mix stirred. Slaking, which turns quicklime into putty, is a hazardous process that gets very hot and can spit, so most applicators start with lime putty that is already slaked. Zavoré teaches limewash, so ask us about limewash training to learn this hands on.

For hands on tuition in decorative plaster finishes, see the courses at the Zavoré Training Academy in Birmingham, and if you would rather have it done for you, our own team provides limewash installation across the UK.

Quicklime, putty and hydrated lime

Lime starts as limestone, which is burned in a kiln to make quicklime. Quicklime reacts strongly with water. This reaction is called slaking, and it releases a great deal of heat. The result, after maturing, is lime putty.

There are three forms you may hear about.

  • Quicklime. The burned lime before water is added. It is caustic and dangerous to handle without training and proper equipment.
  • Lime putty. Slaked lime stored wet as a soft paste. It is the traditional base for limewash and improves as it matures.
  • Hydrated lime. Slaked lime sold as a dry powder in bags.
Lime slaking safety on a limewash course, a white wall with decorative textured stucco

Why slaking is treated with care

When quicklime meets water, the mix can boil, steam and spit hot, caustic material. Burns to skin and eyes are a real risk. Slaking is a job for people with proper training, protective equipment and a safe place to do it.

Good training explains what slaking is and why it matters to the quality of the putty, but for everyday limewash work most applicators buy putty that is already slaked and matured. This removes the most dangerous step from the job site.

Getting the mix right

Mixing limewash from putty is mostly about consistency and care. Training covers.

  • thinning putty with clean water to a thin, milky liquid;
  • sieving the mix to remove lumps and grit;
  • wetting pigment in water first so it spreads evenly before going into the lime;
  • keeping to a limit on pigment, as too much weakens the lime;
  • stirring often, because lime settles in the bucket;
  • writing down every ratio so the colour can be repeated.

A thickener can help adjust consistency for some lime products. Zavoré sells a Thickener for Lime for lime based plasters and paints.

Protecting yourself while mixing

Lime is alkaline and can burn skin and eyes even when it is mixed with water. When mixing, wear waterproof gloves, close fitting eye protection and long sleeves. Wear a suitable dust mask when handling dry powder. Keep clean water and an eyewash bottle within reach. If lime gets in an eye, rinse it with plenty of clean water straight away and get medical help.

Keep children and pets well away from mixing areas, and keep lime in sealed, labelled containers.

Learning it properly

Mixing is easy to describe but hard to judge without seeing it. Training lets you feel the right consistency, see how pigment behaves and learn from mistakes on boards rather than walls. Our guide to how to apply limewash follows on from mixing.

To learn to mix limewash safely and consistently, talk to us. Ask us about limewash training through our contact page, by calling 07592 929191 or by emailing sales@zavore.co.uk. Our training page shows the Venetian plaster courses we currently run, and if you want to see a lime finish in a set colour, you can order a sample board.

Questions we get asked

Do I need to slake my own lime?

No. Most applicators buy lime putty that is already slaked and matured, which avoids the most dangerous step.

Can I use bagged hydrated lime for limewash?

It can be used, though many traditional applicators prefer mature lime putty. Training covers the differences.

What should I do if lime gets in my eye?

Rinse it with plenty of clean water straight away and get medical help.

Back to the Journal

Providing luxury finishes for the most prestigious addresses in the world

Venetian plaster, limewash, microcement, tadelakt, metallics, sculptural plaster and gold leaf, supplied and installed by our own team, with Venetian plaster taught at our Birmingham studio.

PayPal
© 2026 Zavoré Ltd · Est. 2021 · Made to order in Birmingham
For The Trade Three ways to earn with us
Trade accountTen percent off every material in the shop, and a specialist on the phone. Partners & affiliatesGet listed where customers find you, or sell our materials and earn on every order. The Rewards RoomEvery order earns. Samples, tools and an apron, on the house.
Free to join · we reply within 24 hours
EN