ZAVORÉ
ZAVORÉ
✦
Where Artistry Begins
Tracked delivery across the UK and worldwide·Same day and 24 hour delivery available·Venetian plaster tinted to your exact colour·Damaged in transit? We’ll replace it within 24 hours or on the same day·Speak to a specialist · 07592 929191·Residential and commercial projects installed by our own team·Trade accounts · 10% and rewards·Training courses at our studio·Showroom · visit by appointment·Tracked delivery across the UK and worldwide·Same day and 24 hour delivery available·Venetian plaster tinted to your exact colour·Damaged in transit? We’ll replace it within 24 hours or on the same day·Speak to a specialist · 07592 929191·Residential and commercial projects installed by our own team·Trade accounts · 10% and rewards·Training courses at our studio·Showroom · visit by appointment·
Home/The Journal/Marble Dust Plaster and Additives, What Each One Does to a Finish
19 September 2026

Marble Dust Plaster and Additives, What Each One Does to a Finish

Close view of a white textured plaster wall with soft ridges and hollows, marble dust and plaster additives

Marble dust plaster is a lime plaster with extra crushed marble mixed in to give it more body and texture, and marble powder is the most common of several additives used to change how a decorative plaster looks or behaves. Some additives change the look, such as mica, mother of pearl, glitter, milled marbles and sand. Others change the working, such as slow drying and strong adhesion additives and lime thickener. Used well, each one does a specific job. Used carelessly, most of them spoil a finish. This guide goes through them one by one.

The one rule for every additive

Whatever you add, add the same amount to every tub for the same wall, mix it in thoroughly, and try it on a test board before it goes near the wall. An additive changes the plaster. If one tub gets more than another, the finish changes where the tubs change, and on a large wall that shows as a band. Weigh or measure; do not add by eye.

Additives that change the look

Marble powder

Marble Powder (£14) is finely ground natural marble in Fine and Medium grades. It adds body, smooth texture and aggregate to a decorative plaster. Plasterers use it to stiffen a mix, to build a fuller base coat, or to push a finish towards a slightly more textured, stony surface.

When it spoils a finish: marble changes the balance of binder to aggregate. Add too much and the coat is weak, dusty and will not close or polish. If you want a high polish, keep it light or leave it out.

Three milled marbles

Three Milled Marbles (£13) is a blend of three grades of milled marble. Where marble powder smooths and bulks, the mixed grades give visible texture and a multi tonal stone effect. It suits textured marmorino and stone style walls.

When it spoils a finish: coarse grains drag under a polishing trowel and leave scratches. Keep it out of anything meant to be glassy.

Sand

Sand Salt & Pepper (£7) is a two tone black and white sand that gives a speckled granular texture. It works in textured decorative plasters where you want the grain to be seen.

When it spoils a finish: it is a strong look. On a large wall it can read busy, and like any coarse aggregate it does not belong in a polished coat.

Mica

Mica Silver (£9) is natural silver mica flake. Mixed into the plaster or laid on as a top coat, it gives a metallic shimmer that moves as you walk past.

When it spoils a finish: a little goes a long way. Overdone, the wall looks glittery rather than mineral, and loose flakes on the surface can catch under a trowel.

Mother of pearl

Mother of Pearl (£10) is an iridescent additive in Fine, Medium and Coarse grades. It gives a soft, shifting shimmer in Veneziano and other decorative plasters. The fine grade gives a gentle glow; the coarse grade gives distinct points of light.

When it spoils a finish: coarse mother of pearl in a high polish finish can leave marks where the trowel drags a particle. Match the grade to the finish.

Glitter

Glitter (£8) comes in silver and gold. It can be mixed into Veneziano, Stucco Crea and other decorative plasters, or scattered on the surface, for anything from a faint sparkle to a bold one.

When it spoils a finish: glitter is the easiest additive to overuse. In a quiet room it can look cheap. Try it in a small dose on a board and look at it in the room before committing.

Additives that change how the plaster works

Slow drying additive

Slow Drying Additive (£16) extends the open time of decorative plasters, meaning how long the coat stays workable on the wall. It helps on large walls, on complex textures and in warm, dry rooms where plaster goes off before you have finished working it.

When it spoils a finish: in a cold, damp room plaster already stays wet a long time. Slowing it further keeps it soft and increases the risk of lime bloom, the white veil that forms when lime is carried to the surface as it dries. Use it to fix a fast room, not as a habit.

Strong adhesion additive

Strong Adhesion Additive (£15) is made for Pastellone and other lime plasters and improves bonding on smooth, dense or non absorbent backgrounds.

When it spoils a finish: it is not a substitute for preparation. A dusty, flaking or damp background will still fail. Clean and prime properly with a suitable primer first, and use the additive where the background is sound but difficult. Our piece on why marmorino cracks covers background problems in more detail.

Lime thickener

Thickener for Lime (£17) adjusts the consistency of lime based plasters and paints. It makes a mix thicker without changing its open time or final finish. It is useful when a lime paint or limewash runs on a wall, or when you want a heavier coat to hold texture.

When it spoils a finish: a limewash is meant to be thin and to build in soft layers. Thicken it too far and you lose the cloudy, layered look that is the reason for using it. See our limewash page for what the finish should look like.

Plaster additives at a glance

Additive What it does Use it for Keep it out of
Marble powder Adds body and smooth texture Base coats, stiffer mixes High polish, in large amounts
Three milled marbles Visible multi grade texture Textured marmorino, stone looks Polished plaster
Sand salt & pepper Two tone speckled grain Textured decorative walls Polished coats, quiet rooms
Mica Metallic shimmer Feature walls, top coats Large doses anywhere
Mother of pearl Iridescent glow Veneziano, feature walls Coarse grade in high polish
Glitter Sparkle Small features, bold looks Calm, mineral finishes
Slow drying Longer open time Large walls, warm dry rooms Cold, damp rooms
Strong adhesion Better bond on dense backgrounds Smooth, non absorbent substrates Unsound backgrounds
Lime thickener Thicker consistency Runny lime paints, heavy coats Limewash meant to stay thin

For the finishes these additives feed into, our guide to Venetian plaster textures and finishes shows the range, and our marmorino page covers the finish most often textured with marble.

Questions we get asked

What is marble dust used for in plaster?

Marble dust is the aggregate in Venetian and other lime plasters. It gives the coat body so it does not shrink and craze, makes the cured surface harder, and, in fine grades, lets the trowel close the surface to a polish. Added separately, marble powder stiffens a mix or builds a fuller base coat. Too much weakens the coat.

Can you mix glitter into Venetian plaster?

Yes. Glitter can be mixed into Veneziano, Stucco Crea and other decorative plasters, or scattered on the surface. Add a measured amount, the same in every tub for one wall, and try it on a board first. Glitter is easy to overdo, and a wall that looks fun on a sample can look cheap across a whole room.

How do you make plaster dry slower?

Mix in a slow drying additive, which extends how long the plaster stays workable. It helps on large walls and in warm, dry rooms. Keep windows and heaters from blowing straight onto the wall while you work. Do not use a slow drying additive in a cold, damp room, where the plaster already stays wet and lime bloom is more likely.

What is mother of pearl in plaster?

Mother of pearl is an iridescent additive, sold in fine, medium and coarse grades, that gives a decorative plaster a soft shifting shimmer. Fine grades give an even glow and suit polished finishes. Coarse grades give distinct points of light but can drag under a polishing trowel, so they suit textured finishes better.

Where to go next: every additive listed here is in the shop, and the Advanced course on our training page covers tinting, blending and building finishes in the studio.

Back to the Journal

Providing luxury finishes for the most prestigious addresses in the world

Venetian plaster, limewash, microcement, tadelakt, metallics, sculptural plaster and gold leaf, supplied and installed by our own team, with Venetian plaster taught at our Birmingham studio.

PayPal
© 2026 Zavoré Ltd · Est. 2021 · Made to order in Birmingham
For The Trade Three ways to earn with us
Trade accountTen percent off every material in the shop, and a specialist on the phone. Partners & affiliatesGet listed where customers find you, or sell our materials and earn on every order. The Rewards RoomEvery order earns. Samples, tools and an apron, on the house.
Free to join · we reply within 24 hours
EN