


Venetian plastering techniques come down to four skills done in order, which are preparing a flat, primed wall, laying very thin coats of lime and marble with a flexible steel trowel, burnishing the final coat until it shines, and buffing in a wax. Zavoré uses these techniques on every wall our artisans finish and teaches them in person at our centres in England. The depth people admire comes from the layering, not from any one coat.
If you are new to the material, start with our Venetian plaster page, which explains what it is made of. For finished walls rather than learning, we offer Venetian plastering across the UK. This guide walks through the craft itself, coat by coat, so you know what is happening on your wall or what you would practise on a course.
Every technique that follows depends on the base. The wall must be sound, clean and flat, because a burnished surface picks up each hollow and ridge beneath it. On plasterboard, joints are taped and reinforced and screw heads filled. On old masonry, loose plaster is cut back and repaired, and old paint that would stop lime bonding is removed. Damp is cured before anything decorative goes on.
Then comes the primer. The right primer gives the first coat something to grip and evens out how fast the wall draws moisture from the plaster. Skipping or mismatching it is one of the commonest reasons a finish fails, so it is treated as part of the craft, not an afterthought.
The first coat is a thin, even layer that builds the foundation of colour and texture. It is scooped onto a hawk, picked up on the edge of a flexible steel trowel and pressed onto the wall in short, overlapping strokes. The aim is full coverage with very little material, closer to a skin than a layer you could measure easily.
Good first coats look unremarkable. They should be consistent, free of ridges and laid without stopping mid wall, because a hard line where work paused can show through later. Lime is caustic while wet, so gloves and eye protection are worn and floors and joinery are covered before the tub is opened.
Depth is the heart of the finish. Each further coat is applied thinly over the last once it is ready, and the artisan varies the direction, pressure and angle of the trowel so that some areas carry more material and others less. Where tones are layered, the lower coats show faintly through the upper ones, which gives the clouded, stone like movement associated with marble.
How many coats a wall takes depends on the finish and the look you want. A Marmorino finish stays more matt, with a fine stone grain, while a full polished Venetian plaster is built up for glassy depth. Travertino, another lime finish, is worked differently again, with pores made in the wet material and horizontal trowel passes that line up to suggest bedding planes in stone. The material is the same family, but the hand makes the finish.
Burnishing is what turns a coloured wall into a polished one. As the final coat begins to firm up, the artisan passes a clean steel trowel over it again and again, pressing hard and holding the blade almost flat. This compresses and closes the surface, so the wall develops a sheen of its own without any gloss paint.
Timing is everything. Burnish too early and the trowel drags the plaster. Leave it too late and the surface will not take a shine. Judging that moment by touch and sound is one of the main things students practise, and it is why long walls are often worked by two people so the whole surface reaches the same point together.
Once the wall has dried, a natural wax is applied in a very thin film, usually with a soft cloth or a steel trowel, and then buffed by hand. Wax deepens the colour slightly, adds a soft lustre and gives the surface protection against everyday marks. It also makes the wall easier to wipe clean.
Wax is not a waterproof barrier. Venetian plaster is not for inside a shower, where tadelakt, or microcement over a waterproofed wall, is used instead. Around a basin or in a cloakroom, a waxed Venetian finish copes well with splashes.
The trowel movements look similar, but the materials behave differently. Lime breathes and suits solid masonry. Acrylic forms a film on the surface instead. Ours is lime based, and the techniques we teach are built around how lime handles, sets and polishes.
Whichever material is used, Venetian plaster gives a marble look but is not marble. Understanding that helps set expectations. It is a craft finish with natural variation, and that variation is part of what people pay for.
We teach in person only, at the Zavoré Academy in Birmingham, opened in 2023, and at our London and Manchester centres. All courses run at all three. The Beginner Course lasts 3 days, the Advanced Course 4 days and 1 to 1 Training 3 days, with all materials included. Every course is taught face to face, because these techniques are learned by feel with a trowel in hand. Our training page lists dates and details.
It depends on the finish and the depth you want. A Marmorino may need fewer coats than a deep polished Venetian plaster built up in layers. Each coat is very thin and laid only when the one beneath it is ready, which is why the work is planned in blocks of days.
A flexible steel trowel is the main tool, used with a hawk to hold the plaster. The flex in the blade lets the artisan vary pressure while laying the coats and again while burnishing the last one.
Yes. Burnishing is one of the skills students practise on our courses, and timing is usually the hardest part to judge. Working on boards under guidance, with real lime materials, is how you learn to feel when the surface is ready.
For a polished Venetian finish, wax is the usual last step because it protects the surface and deepens the colour. The final treatment for each finish is shown on the sample, so you approve it before any wall is started.
For a wall finished by our artisans or a place on a course, call +44 7592 929191 between 9am and 6pm, Monday to Saturday, or email sales@zavore.co.uk. For installations, send photos, rough measurements and the address, and order a sample board to see the finish in person.
An outline of what limewash training covers about mixing limewash and the risks of slaking lime, and how to ask Zavoré about it.
BasementsA guide to decorative finishes for London basements, covering media rooms, gyms and wine rooms, why waterproofing must come first, and wh...
CheshireAn in depth guide to seamless microcement and tadelakt bathrooms for homes across Cheshire, and how to choose between them.
CheshireA guide to polished plaster and other decorative finishes for the large modern homes of Wilmslow and Alderley Edge, and where they fit in...
CheshireChester and the Cheshire countryside are full of timber framed, Georgian and Victorian buildings. This guide explains why lime finishes s...
Greater ManchesterHow microcement floors work in kitchen extensions across Greater Manchester, from the screed underneath to underfloor heating and everyda...
Providing luxury finishes for the most prestigious addresses in the world
Venetian plaster, limewash, microcement, tadelakt, metallics, sculptural plaster and gold leaf, supplied and installed by our own team, with Venetian plaster taught at our Birmingham studio.
One list, run by the people who make the material. No noise, and nothing we would not want to read ourselves.
We email as the house has something worth saying, never daily. Unsubscribe from any email, or reply STOP to any text. We never pass your details to anyone.