ZAVORÉ
ZAVORÉ
✦
Where Artistry Begins
Tracked delivery across the UK and worldwide·Same day and 24 hour delivery available·Venetian plaster tinted to your exact colour·Damaged in transit? We’ll replace it within 24 hours or on the same day·Speak to a specialist · 07592 929191·Residential and commercial projects installed by our own team·Trade accounts · 10% and rewards·Training courses at our studio·Showroom · visit by appointment·Tracked delivery across the UK and worldwide·Same day and 24 hour delivery available·Venetian plaster tinted to your exact colour·Damaged in transit? We’ll replace it within 24 hours or on the same day·Speak to a specialist · 07592 929191·Residential and commercial projects installed by our own team·Trade accounts · 10% and rewards·Training courses at our studio·Showroom · visit by appointment·
Home/The Journal/Microcement Over Tiles, When It Works, When Tiles Come Off
19 September 2026

Microcement Over Tiles, When It Works, When Tiles Come Off

A modern bathroom with a seamless finish, a bath, basin and shower, laying microcement over tiles

Microcement over tiles works, and it is one of the most common ways the material is used in British homes. The existing tiles stay where they are: they are washed, degreased, keyed, primed, the grout lines are filled flush, and two or three thin coats of microcement are trowelled over the top and sealed. The single condition is that the tiles are sound and firmly bonded to what is behind them. Hollow, loose, drummy or cracked tiles come off first, because microcement is a few millimetres thick and cannot hold down something that is already letting go. This article is about telling the difference, and about what the preparation really involves. For what the material is in the first place, start at our microcement page.

Would you rather have it done for you? Our own applicators provide microcement installation across the UK.

When microcement over tiles works

It works when the tiles are a stable surface in their own right. That means every tile is stuck down across its full bed, the substrate behind them is dry and not moving, and there is nothing going on underneath that a new finish would only hide. Ceramic, porcelain, natural stone, quarry tiles and even old mosaic all take microcement, because the bond is made by the primer rather than by the tile face itself.

Glazed porcelain is the one people worry about, and it is fine. A dense, glassy glaze is a poor surface to bond to on its own, so it gets mechanically abraded and then a high grip adhesion primer, usually a quartz filled one that dries to a gritty texture. Once that primer is on, the microcement is bonding to primer, not to glaze.

A tiled wall or floor is also usually flat and already level, which removes half the preparation a bare substrate would need.

When the tiles have to come off

Take them off when any of the following is true.

  • They sound hollow when tapped, which means the tile is bridging a void.
  • They are loose, lifting at a corner, or you can rock one with a thumb.
  • Tiles are cracked in a line across several of them, which usually means the substrate below is moving or a joist is deflecting.
  • There is damp coming through, a failed tray, or a leak that has not been traced.
  • They are fixed to a timber floor that bounces, or to boards that were never rigid enough.
  • The build up would put the floor above a threshold or under a door that cannot be trimmed.

Test before anyone quotes, not after. Tap across the whole area with a screwdriver handle and listen: a bonded tile gives a dull, solid note, a hollow one rings. Mark anything that rings. A handful come out, the void is filled and levelled, and the rest stays. If a third of the floor rings, strip it out.

The rule we work to is simple. Microcement does not make a bad substrate good. It makes a good substrate seamless.

Keying and priming

Preparation over tiles runs in a set order, and skipping any of it is where failures come from.

First, clean. Bathroom tiles carry soap and limescale; kitchen tiles carry grease. A degreaser and a proper rinse, then let it dry. Nothing bonds to a film of soap.

Second, key. The glaze is abraded so the primer has something to hold. By hand on a small area, by machine with extraction on a large one, and either way it is a dusty hour that needs the room sheeted and masked.

Third, prime. An adhesion primer suited to non absorbent surfaces goes on and cures for as long as the system says, not as long as the programme would like. Many systems then want a reinforcing mesh bedded into the first coat, and on a tiled substrate we would always use it.

Filling the grout lines

Grout joints are the reason a tiled overlay ghosts. The microcement coats are thin, and thin coats shrink very slightly as they dry. If a joint is still an open channel when the finish goes on, that channel will telegraph through as a faint grid you will only see in low winter light across a wall, and then you will see nothing else.

The fix is to fill the joints as a separate step before the body coats, flush with the tile face, then let that filler cure and flatten it back. Narrow joints in large format porcelain take one pass; deep or raked joints in old quarry tile take two. Mosaic, which is mostly joint, often argues for a levelling layer across the whole area instead.

Movement, junctions and where it still cracks

A seamless finish has no joints to absorb movement, so the movement has to be dealt with underneath. Existing expansion joints in a tiled floor are carried through the microcement, not buried. Junctions between floor and wall, around baths and trays, and where the finish meets glass or metal, are filled with a flexible sealant rather than trowelled hard into a corner. Two substrates meeting under one coating, tile running into plasterboard, want a mesh over the join at the very least.

What going over tiles actually saves

Strip out and retile Microcement over tiles
Demolition Tiles, adhesive bed, often the board behind None, beyond isolated loose tiles
Waste Skip, and carrying rubble through the house Bags of dust and sheeting
Tanking Redone from scratch in wet areas Existing tanking left undisturbed
Room out of use Typically a week or more Typically days, plus sealer cure
Risk Whatever you find behind the tiles Whatever the tapping test missed

The saving people underestimate is the mess. Stripping tiles off a plastered wall usually takes the plaster with it, turning a bathroom refresh into a replastering job. The saving people overestimate is money: the materials are dearer and the labour is skilled and slow, so the win is time and disruption rather than a smaller invoice. We set that out in microcement versus tiles.

The lime alternative, and what we stock

Zavoré supplies and installs microcement. We also sell the lime family that does the same seamless job with different chemistry: Tadelakt, the soap sealed Moroccan lime plaster for wet areas, Pastellone for continuous lime floors and walls, and Beton Stucco for a flat concrete look. All three go over sound tiles on the same principle: clean, key, prime, fill the joints. Lime over tiles is less forgiving than cement based microcement and wants a plasterer who has done it, so if you are specifying rather than laying, read our microcement bathroom guide alongside the Tadelakt page before you commit.

Questions we get asked

Can you really put microcement straight onto tiles?

Yes, provided the tiles are sound and well bonded. They are degreased, mechanically keyed, primed with an adhesion primer made for non absorbent surfaces, and the grout lines are filled flush before the body coats go on. The bond is made by the primer, not the tile face, which is why glazed porcelain is not a problem.

How do I know if my tiles are sound enough?

Tap across the whole area with your knuckles or a screwdriver handle. A bonded tile sounds dull and solid; a hollow one rings. Mark every tile that rings. A few can be cut out, filled and levelled. If a large share of them ring, or the floor flexes underfoot, strip out instead.

Will the grout lines show through afterwards?

Only if they were not filled properly. Joints must be filled flush and allowed to cure as a separate step before the finish coats, because thin coats shrink slightly and an unfilled channel telegraphs as a faint grid. Deep or wide joints need two passes. Mosaic often needs a levelling layer over the whole area.

Do you run a microcement course?

No. The Zavoré Academy in Birmingham teaches Venetian plaster, Marmorino, polished plaster, metallics and the lime finishes we supply, across a three day beginner course, a four day advanced course and one to one training. We do not teach microcement, and we would rather say so than sell you the wrong three days.

Where to go next: if you want the work done, our installation team covers the UK from Birmingham and will tap test before quoting. If you lay plaster yourself and want the lime route over tiles, the materials are in the shop, and the Academy covers the finishes we do teach.

Back to the Journal

Providing luxury finishes for the most prestigious addresses in the world

Venetian plaster, limewash, microcement, tadelakt, metallics, sculptural plaster and gold leaf, supplied and installed by our own team, with Venetian plaster taught at our Birmingham studio.

PayPal
© 2026 Zavoré Ltd · Est. 2021 · Made to order in Birmingham
For The Trade Three ways to earn with us
Trade accountTen percent off every material in the shop, and a specialist on the phone. Partners & affiliatesGet listed where customers find you, or sell our materials and earn on every order. The Rewards RoomEvery order earns. Samples, tools and an apron, on the house.
Free to join · we reply within 24 hours
NL