ZAVORÉ
ZAVORÉ
✦
Where Artistry Begins
Tracked delivery across the UK and worldwide·Same day and 24 hour delivery available·Venetian plaster tinted to your exact colour·Damaged in transit? We’ll replace it within 24 hours or on the same day·Speak to a specialist · 07592 929191·Residential and commercial projects installed by our own team·Trade accounts · 10% and rewards·Training courses at our studio·Showroom · visit by appointment·Tracked delivery across the UK and worldwide·Same day and 24 hour delivery available·Venetian plaster tinted to your exact colour·Damaged in transit? We’ll replace it within 24 hours or on the same day·Speak to a specialist · 07592 929191·Residential and commercial projects installed by our own team·Trade accounts · 10% and rewards·Training courses at our studio·Showroom · visit by appointment·
Home/The Journal/Microcement Floors in UK Homes, What Each Layer Needs From Substrate to Sealer
19 September 2026

Microcement Floors in UK Homes, What Each Layer Needs From Substrate to Sealer

A grey concrete effect surface with a subtle mottled texture, microcement floors in UK homes

A microcement floor is a seamless, jointless floor finish laid in thin trowelled coats over an existing substrate and sealed on top. It suits UK homes because it is only a few millimetres thick, so it clears doors and thresholds where tile or stone would not, it works over underfloor heating, and it can go over an existing tiled or screeded floor without a strip out. What it will not do is fix a floor that moves. Microcement flooring is a finish, not a structure: it takes on the behaviour of whatever is underneath it, and almost every failure we are called to look at began below the coating rather than in it. This is what to get right. For the material itself, see our microcement page.

Zavoré lays this for you too. Our own team provides microcement installation across the UK.

The substrate decides everything

Microcement bonds to a sound, dry, rigid, flat base. Each of those four words is doing work.

Sound means nothing loose, dusty, contaminated or delaminating. Old adhesive residue, paint, and a screed that crumbles under a screwdriver are all dealt with before anything else happens.

Dry means a new screed or slab has given up its construction moisture before it is sealed in. A modern sealer is a closed film: trap moisture beneath it and you get blistering and dark patching that no buffing will clear. New concrete and sand cement screeds dry slowly, more slowly than most programmes allow, and a moisture reading beats a guess.

Rigid is where timber floors get interesting. A suspended timber floor moves as people walk on it and as the seasons change, and a thin, hard, jointless coating over a floor that deflects will crack in a straight line over the joist or board joint. Timber floors need overboarding or a rigid board system, fixed at close centres, before anyone talks about finish.

Flat matters because the coating is too thin to level anything. Hollows, ridges and falls are corrected in a levelling layer first. This is the step cut when a price is squeezed, and it shows for the life of the floor.

Movement joints are not optional

A seamless floor has nowhere for movement to go, so it goes into a crack. Existing movement joints and day joints in the slab are carried up through the microcement and finished as joints, not bridged and hidden. Doorway thresholds between rooms and the junction where floor meets wall want the same thinking: a flexible detail rather than a rigid one. Perimeters are the ones people forget, a compressible detail hidden by the skirting gives the floor somewhere to breathe.

Underfloor heating

Microcement and underfloor heating suit each other. The coating is thin and dense, so heat comes through quickly and the floor feels responsive rather than sluggish, and it is warmer underfoot than porcelain.

The conditions are about commissioning rather than the finish. The heating should be fully commissioned and cycled through its heat up and cool down before the finish goes on, so the screed has done its expanding and contracting first. It is then turned off and the floor brought back to ambient for the application, and brought back up slowly afterwards rather than switched straight to a winter setting.

Electric mat systems want particular care: the mat and its levelling layer must be fully encapsulated and flat, because any ridge over a cable will read through a few millimetres of finish.

Thresholds and thickness

This is the practical reason microcement gets specified in refurbishments. Tile plus adhesive, or stone plus bed, adds enough height to foul doors, stop a wheelchair, or leave a lip at every threshold. A trowelled coating adds very little, so one continuous floor can run from hall to kitchen to utility with no trim at each doorway.

It also makes going over an existing tiled floor realistic where relaying would not be. The tiles are tested, keyed, primed and the joints filled first. The sequence is in microcement versus tiles, and the floor level barely changes.

Slip resistance

A microcement floor is as slippery or as grippy as its sealer, and that is a specification decision rather than an afterthought. A high gloss sealer on a large open floor looks superb in a photograph and is a poor idea in a shower, a wet room, a family bathroom or a kitchen by a back door.

Matt sealers grip better than gloss. Anti slip additives can be broadcast into the final sealer coats selectively: grippier in the shower zone, smoother across the main bathroom floor, so the room still reads as one surface. Anywhere a floor gets wet in use, ask which sealer, how many coats, and what slip classification the system is tested to.

Sealing, curing and living on it

The sealer is the wearing surface. The microcement gives you the look; the sealer gives you the resistance to water, wine, dog claws and grit. Most floor systems use a two part polyurethane built up in coats, and the cure time before heavy use is far longer than the touch dry time. Walk on it too early, drag a fridge across it, or put rugs down before it has cured, and you have marked a floor you then live with.

Day to day it is easy: vacuum grit, damp mop with a pH neutral cleaner, and keep bleach, limescale removers and abrasive pads away from it. Grit is the real enemy, so mats at external doors do more good than any product. A worn sealer can be abraded and recoated without replacing the finish beneath, which is the quiet advantage of a coating over a tile. The care principles are the same ones in how to maintain Venetian plaster.

Where microcement floors fail

In this order: movement in the substrate that was never addressed; moisture rising through a slab sealed too soon; a levelling layer skipped to save a day; bridged movement joints; and a sealer rushed, under coated or walked on before it cured. Four of the five happen before the finish coat goes on.

What we stock

Zavoré supplies and installs microcement floors. The other floor materials we supply are lime based: Pastellone, the traditional Italian polished lime floor, which gives a continuous jointless surface with real depth to it, and Beton Stucco for a flatter concrete look on floors and walls. In wet rooms, Tadelakt is the lime answer to a sealed shower floor. They follow different rules, breathable, soap or wax sealed rather than resin sealed, and no more tolerant of a poor substrate. Our concrete effect page covers the look; the shop has the tubs.

For a traditional Italian lime floor, read our pastellone floors guide.

Questions we get asked

Can you put a microcement floor over underfloor heating?

Yes, and it performs well because the coating is thin and conducts heat quickly. The heating must be commissioned and cycled through a full heat up and cool down before application, then turned off and the floor returned to ambient while the coats go on, and brought back up gradually afterwards rather than switched straight to full output.

Will a microcement floor crack?

Not if the substrate is rigid, dry and flat, and existing movement joints are carried through rather than bridged. Cracks almost always trace back to deflection in a timber floor, a slab that was still drying, a skipped levelling layer or a buried joint. The coating simply reports what the floor underneath is doing.

Is a microcement floor slippery when wet?

That depends entirely on the sealer. Gloss sealers are slippery wet; matt sealers grip better; anti slip additives can be broadcast into the final coats where they are needed. In bathrooms and wet rooms ask for anti slip in the shower zone and a smoother finish elsewhere, and ask what slip rating the sealer system is tested to.

How thick is a microcement floor?

Only a few millimetres once the coats and sealer are built up, which is why it clears doors and thresholds that tile or stone would foul. That thinness is also the limitation: it cannot level a floor or correct a fall, so any hollows, ridges or slopes have to be sorted in a levelling layer before the finish starts.

Where to go next: for a floor survey and a proper look at your substrate, talk to our installation team. If you lay floors yourself and want the lime route, start with Pastellone in the shop and read the Tadelakt page for wet areas.

Back to the Journal

Providing luxury finishes for the most prestigious addresses in the world

Venetian plaster, limewash, microcement, tadelakt, metallics, sculptural plaster and gold leaf, supplied and installed by our own team, with Venetian plaster taught at our Birmingham studio.

PayPal
© 2026 Zavoré Ltd · Est. 2021 · Made to order in Birmingham
For The Trade Three ways to earn with us
Trade accountTen percent off every material in the shop, and a specialist on the phone. Partners & affiliatesGet listed where customers find you, or sell our materials and earn on every order. The Rewards RoomEvery order earns. Samples, tools and an apron, on the house.
Free to join · we reply within 24 hours
EN